1968 Fender Telecaster: Blonde refinish & repair - UPDATED!

  • Posted by Krishna
  • at 10/04/2008 12:55:00 AM -
  • 2 comments
This project belongs to a customer who found this 1968 Telecaster that had been through a lot of changes but offered the basis for an excellent restoration. The guitar body had been stripped and routed for humbuckers. In addition, the body had some serious dinging/denting on the rear from being played with no finish. On the plus side, the body is probably the lightest Fender guitar body I have ever come across.

The remnants of the finish in the neck pocket and control cavity revealed that Telecaster had the classic blonde finish originally. I showed the owner my long dormant project 1966 Telecaster and we agreed I'd try to replicate its blonde finish. The Tele blonde finish differs from the Olympic White finish Fender used during the 60s in that it was translucent, so that some of the grain is actually visible through the finish. This also obviously meant that this finish uses no white primer coat - and just a thin color coat, with a clear topcoat that yellows to give the characteristic buttery look of 60s Teles.

Below is a picture of my 66 Tele - one day I'll fix those routes on this baby and post its story - which is pretty wacky !!



Note how much lighter the color of the body is under the guard. A look at the edge of the body where there has been wear reveals that this Tele was probably almost white when it was new, but aging gave it the classic Tele look.




The first step was to clean up the routes to allow for gluing in of clean plugs prior to re-routing for the neck pickup and the diagonal wiring rout. I decided to plug the routes with maple, since I didn't have any ash for plugging and the color of the maple was similar to the light colored ash of the body.



Once the routing was complete, the plugs were cut and glued in place. A few small pieces were also glued in to fill in some gaps, also of maple.






With the body plugged, it was time to layout the re-routing of the body. The owner decided to install a strat pickup in the neck position and requested I rout for the slightly larger size pickup. Other than that, I tried to make the routing as close to stock as possible.



The rear of the body had some dings and grooves pressed into the wood - presumably from someone's huge ZZ Top belt-buckle during the 70s! I used the classic dent steaming technique - in whish the wood is first wetted with water, and then a soldering iron with a wet cloth is placed against the dented area to swell the wood back up. This approach successfully popped out some of the dents and grooves on the back, though one area along a grain like appeared to actually be worn away, maybe during the stripping process years before. As I noted - this Tele had a very lightweight - and soft - ash body.



The body edges were then block sanded and hand sanded with 220 grit paper - and the body was finally ready for a vinyl sealer coat.

Two heavy coats were applied - with some light sanding of the front and back faces of the body with 320 grit paper afterwards. The body was now ready for its first color coat.



To mix the color coat, I started with standard gloss white nitro lacquer (from my friends at Eastern Chem-Lac) and added a small amount of Sheffield's Tintsall Medium Yellow, which sort of an ochre color pigment paste. A little goes a LONG WAY .. so just add a little at a time - mix thoroughly - and then add more if needed. Otherwise you may end up in a Pee Wee Herman-esque "Ice Cream Soup" situation (look it up on YouTube if you have no idea what I'm talking about ...).

Once I had a small jar of the buttery color I wanted (I compared it to paint that was in the pickup routings of my 66 Tele), I mixed it 1 part color to 2 parts clear gloss nitro, and then thinned it for spraying. I mixed up plenty so I'd have enough for any resprays I'd have to do on the guitar.



The key is to be patient and build up the color slowly - again, the goal was to achieve a translucent finish that left the grain of the ash just barely visible.

I sprayed the routing repair area first, since I wanted to do as much as possible to hide the patches in that area (though they will be under a pickguard) - and then I applied an even light coat over the entire body - spraying each surface with 3 or 4 passes. As you can see - the grain is very prominent, but the color is getting there.




After letting the first coat dry for about an hour, I added a second heavier coat - I planned on this being the final color coat - any additional darkening will come from an aged/ambered clearcoat.

The opacity ended up much higher after the second coat - which was accomplished with about 4 passes over all the surfaces, including the edges. However, the second picture below, the close-up, reveals that the grain is still visible - this is probably very much what a 68 Telecaster looked like new from the factory IN 1968. But a nice aged topcoat will give this Tele the familiar "old Telecaster" look when I'm done.




(Update - October 17th, 2008)
The open grained ash of this light-weight Telecaster required many clear coats - followed by wet sanding - to level the grain with the rest of the surface. In retrospect, the body should have probably received several extra coats of sealer BEFORE the color coat, but the difficulty is seeing the grain when using a clear sealer coat. One of the many reasons solid-color finishes are so much easier - the white primer really highlights any imperfections and open grain.

But finally - a nice smooth finish was achieved, and the Telecaster was reading for the "aged" clear coat that would darken the finish to a more vintage look. The owner and I decided to simulate the uneven yellowing that occurs between areas on the guitar body that are covered by hardware and those that are not.

I once again used my 66 Telecaster as a guide - the picture below illustrates the difference in color between covered and uncovered areas.



I then cut cardboard forms out to cover the areas I didn't want to tint - fitting them to the 66 Tele as a check.



The next step was to come up with a good level of tinting for the clear lacquer coat - its easy to overdo it at this stage and give the guitar a very bogus look - or to get a run in the clear coat and ruin a paint job right near the end (this is one reason I generally don't offer to do aged clearcoats - though I may start offering it as an option).

I had sprayed a test piece of masonite with the buttery-tinted white finish I used as the color coat on the Tele - and I used this to test out my tinting to see if I'd get the desired results and make sure I had a mixture that was controllable in terms of the stregth and depth of color.



Then I attached the cardboard forms to the Tele body - using small pieces of cardboard as spacers to slightly raise the forms off the surface of the guitar body - this gives the untinted areas a slightly soft edge - which is what is seen on genuine vintage finishes. Note how you can still just see the grain of the ash through the blonde finish (click on the image to see a full-size view).




Now the spraying ! I did it in three light coats - doing the front, back and edges - waiting a few minutes - and then again - trying to make the tinting as even as I could. The lighting is a little off in this picture, so the body looks darker than it is.




But for a real impression of the results - the unmasking !

Compare this to the picture of the 66 body further back in the post - its a similar effect, though not tinted as dark. The final step will be another clear coat over the tinted coat to seal it in and allow me to do a final wet sanding and buffing of the finish without cutting into the tinted coat inadvertently.



It will be possible for the owner to get a more "relic'd" look by taking sandpaper to the edges of the body - which will reveal the untinted blonde color and eventually the sealed ash underneath - much like on my 66 Telecaster.

(Update Nov. 1, 2008)

The owner has assembled the Tele and given it a workout - and been kind enough to snap a few pictures of the complete instrument. Note that these are all original parts he's managed to gather up - including the case I believe !!

I have to get my '66 put together .. someday ...








Author

Written by Admin

Aliquam molestie ligula vitae nunc lobortis dictum varius tellus porttitor. Suspendisse vehicula diam a ligula malesuada a pellentesque turpis facilisis. Vestibulum a urna elit. Nulla bibendum dolor suscipit tortor euismod eu laoreet odio facilisis.

2 comments:

  1. Greetings Krishna,

    I got the Telecaster reassembled and it is as remarkable sounding as we both figured it would be. I think it is only fitting, as your work to restore and refinish the body came out spectacular and I would hate to waste your efforts on a mediocre sounding guitar! The blonde color is perfect, to me it looks just like the finishes from the 1950s and the wood grain is accented perfectly. The blending of the new finish with the remnants in the body cavities is perfect, beyond belief, and the aging coat with the masking came out perfect. Thanks again for the exceptional work and for taking the time to work with me and asking the right questions to get this right. It's always great to bring a fine piece like this back to life, and even more so when the work is first class.

    ReplyDelete
  2. Hey thanks for sharing this. A friend of mine is giving me a tele look alike kit, and I am looking at ways to finish the body.

    Glad I found your site!

    ReplyDelete